Door Hanger Roller Hardening Problems

Why Does Elevator Door Hanger Roller Surface Hardening Cause Door Vibration and Noise? In an elevator door system, the elevator door hanger roller supports the door panel and allows it to move smoothly along the door operator track. After long-term use, roller surface materials such as rubber or polyurethane may gradually age and harden. As […]
Escalator Drive Shaft Bearing Problems

Why Does Escalator Main Drive Shaft Bearing Wear Cause Periodic Vibration and Noise? In an escalator drive system, the main drive shaft transfers power to the drive sprockets and related operating components, while the bearings support the shaft and allow it to rotate smoothly and steadily. When the escalator main drive shaft bearings become worn, […]
Old Elevator Safety Circuit Problems

Frequent Intermittent Safety Circuit Faults in Old Elevators? Check These 6 Components During Modernization After many years of operation, older elevators may experience problems such as occasional shutdowns, failure to start after the doors close, or temporary recovery after a system reset. Many of these old elevator faults are related to unstable electrical contact within […]
Old Elevator Leveling Problems

Why Is the Leveling Error of an Old Elevator Getting Worse? After many years of operation, older elevators may develop increasingly noticeable leveling errors, such as the elevator car stopping slightly above or below the landing floor. Elevator leveling accuracy is affected by more than one component. It is usually related to position detection, speed […]
Escalator Newel Guide Wear Problems

Why Does Escalator Newel Guide Component Wear Cause Poor Handrail Return Movement? At the entrance and exit areas of an escalator, the escalator newel not only affects the overall appearance but also guides the handrail as it enters the turnaround area. Inside the newel, there are usually handrail guide rollers, support rollers, or sliding guide […]
Door Encoder Coupling Wear & Position Errors

Why Does Elevator Door Operator Encoder Coupling Wear Cause Door Position Errors? In an elevator door system, the elevator door operator encoder detects the speed and rotational position of the door motor and sends feedback signals to the door operator controller. In some door operator systems, a coupling connects the encoder to the motor shaft. […]
Escalator Comb Plate Clearance Issues

What Problems Can Abnormal Escalator Comb Plate and Step Clearance Cause? During escalator operation, the escalator comb plate is located at the entrance and exit areas and must maintain proper engagement with the grooves of the escalator steps. Correct comb plate engagement allows the steps to enter and leave the landing area smoothly while helping […]
Poor Guide Rail Lubrication Causes Guide Shoe Wear

Why Does Abnormal Elevator Guide Rail Lubricator Oil Supply Accelerate Guide Shoe Wear? In an elevator guiding system, the elevator oil cup or guide rail lubricator continuously supplies an appropriate amount of lubricating oil to the guide rail surface, helping reduce friction between the guide shoes and guide rails. If the oil supply is insufficient, […]
Escalator Indicator Light Problems

What Causes Uneven Brightness or Flickering in Escalator Indicator Lights? During escalator operation, escalator indicator lights are not only used to display operating status but are also an important part of the escalator lighting and display system. When indicator lights show uneven brightness, frequent flickering, or partial illumination failure, the problem may be related to […]
Elevator Button Contact Bounce Issues

Why Does Elevator Button Contact Bounce Cause Signal Fluctuation? In an elevator operating panel, the elevator button converts a passenger's input into an electrical signal through its internal button contacts. After long-term use, contact wear, reduced elasticity, or abnormal return action may cause the contacts to repeatedly make and break within a very short period, […]
Moving Walk Friction Wheel Wear: Causes & Effects

Why Does Moving Walk Handrail Friction Wheel Wear Cause Handrail Slippage? During moving walk operation, the moving walk handrail friction wheel is an important transmission component in the handrail drive system. It transfers driving force through friction between the wheel surface and the handrail. When the friction wheel becomes worn, aged, or its surface condition […]
Elevator Door Lock Contact Signal Failure

Why Does Elevator Door Lock Contact Oxidation Cause Intermittent Door Lock Signal Problems? In an elevator door system, the elevator door lock contact provides feedback to the control system to confirm whether the landing door is securely closed and locked. After long-term use, oxidation, contamination, or reduced contact pressure may increase electrical resistance, causing the […]